Bostitch RC10SQ-E Air Compressor Manual

The Bostitch RC10SQ-E is a compact and efficient air compressor designed for a variety of tasks including inflation, nailing, and powering pneumatic tools. It features a 1.0 HP motor, a 6-gallon tank, and a maximum pressure of 150 PSI. The compressor is lightweight and portable, making it ideal for both home and professional use. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting Devices 7. Operating the Compressor 8. Maintenance 9. Safety Information 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: 6-gallon tank, 1.0 HP motor, maximum pressure of 150 PSI, oil-free pump, and easy-to-read pressure gauges.

Feature	Description
Oil-Free Pump	Requires no maintenance and provides clean air.
Portable Design	Lightweight and easy to transport.
Pressure Gauge	Allows for easy monitoring of pressure levels.
Quick Connect Coupler	Facilitates easy attachment of air hoses.
Safety Valve	Prevents over-pressurization of the tank.

Installation

Unpack the compressor and inspect for any damage. Place it on a stable surface away from moisture.

Connect the air hose to the quick connect coupler.
Ensure the compressor is plugged into a grounded outlet.
Check that the pressure switch is set to the desired PSI.
Turn on the compressor and allow it to build pressure.

WARNING! Always ensure the compressor is on a flat surface to avoid tipping.

First-Time Setup

Power on the compressor and follow the setup instructions.

Set the desired pressure using the pressure regulator.
Connect your pneumatic tool to the air hose.
Test the compressor by running the tool briefly.

CAUTION! Do not exceed the maximum pressure rating of your tools.

Specifications

Tank Size: 6 gallons.
Motor Power: 1.0 HP.
Maximum Pressure: 150 PSI.
Weight: 30 lbs.
Dimensions: 24 x 12 x 23 inches.
Noise Level: 68 dBA.
Power Source: 120V AC.

Controls and Settings

The compressor features a pressure switch, pressure gauge, and on/off switch for easy operation.

Pressure Regulator: Adjusts the output pressure to your tools.

On/Off Switch: Controls the power to the compressor.

Connecting Devices

Ensure the compressor is off before connecting any devices.

Attach the air hose to the quick connect coupler.
Connect your pneumatic tool to the other end of the air hose.
Turn on the compressor and set the desired pressure.

Tip: Always check for leaks after connecting devices.

Operating the Compressor

To operate the compressor, follow these steps:

Turn on the compressor using the on/off switch.
Allow the compressor to build pressure to the set level.
Use your pneumatic tool as needed.
Turn off the compressor when finished.

WARNING! Never operate the compressor in wet conditions.

Maintenance

Regular maintenance is essential for optimal performance.

Check the oil level regularly (if applicable).
Drain the tank of moisture after each use.
Inspect hoses and connections for wear and tear.

CAUTION! Always unplug the compressor before performing maintenance.

Safety Information

Always follow safety guidelines when using the compressor.

Wear appropriate personal protective equipment.
Do not exceed the maximum pressure rating.
Keep the compressor in a dry, well-ventilated area.

Regulatory Information

This compressor complies with all applicable safety standards and regulations. For support, visit www.bostitch.com or contact customer service.

Troubleshooting

Symptom	Possible Cause	Corrective Action
Compressor does not start	Power supply issue	Check power cord and outlet.
Low pressure	Leak in hose	Inspect and replace damaged hoses.
Noisy operation	Loose components	Tighten all screws and bolts.
Overheating	Blocked air intake	Ensure air intake is clear of obstructions.

Reset: Refer to the manual for reset instructions if available.

Service: For service inquiries, contact Bostitch customer support.